command/remote-config: do a pull with `terraform remote config`

command/remote_config.go

@@ -86,29 +86,63 @@ func (c *RemoteConfigCommand) Run(args []string) int {
 		return c.disableRemoteState()
 	}
 
-	// Ensure there is no conflict
+	// Ensure there is no conflict, and then do the correct operation
+	var result int
 	haveCache := !remoteState.Empty()
 	haveLocal := !localState.Empty()
 	switch {
 	case haveCache && haveLocal:
 		c.Ui.Error(fmt.Sprintf("Remote state is enabled, but non-managed state file '%s' is also present!",
 			c.conf.statePath))
-		return 1
+		result = 1
 
 	case !haveCache && !haveLocal:
 		// If we don't have either state file, initialize a blank state file
-		return c.initBlankState()
+		result = c.initBlankState()
 
 	case haveCache && !haveLocal:
 		// Update the remote state target potentially
-		return c.updateRemoteConfig()
+		result = c.updateRemoteConfig()
 
 	case !haveCache && haveLocal:
 		// Enable remote state management
-		return c.enableRemoteState()
+		result = c.enableRemoteState()
+	}
+
+	// If there was an error, return right away
+	if result != 0 {
+		return result
+	}
+
+	// If we're not pulling, then do nothing
+	if !c.conf.pullOnDisable {
+		return result
 	}
 
-	panic("unhandled case")
+	// Otherwise, refresh the state
+	stateResult, err := c.StateRaw(c.StateOpts())
+	if err != nil {
+		c.Ui.Error(fmt.Sprintf(
+			"Error while performing the initial pull. The error message is shown\n"+
+				"below. Note that remote state was properly configured, so you don't\n"+
+				"need to reconfigure. You can now use `push` and `pull` directly.\n"+
+				"\n%s", err))
+		return 1
+	}
+
+	state := stateResult.State
+	if err := state.RefreshState(); err != nil {
+		c.Ui.Error(fmt.Sprintf(
+			"Error while performing the initial pull. The error message is shown\n"+
+				"below. Note that remote state was properly configured, so you don't\n"+
+				"need to reconfigure. You can now use `push` and `pull` directly.\n"+
+				"\n%s", err))
+		return 1
+	}
+
+	c.Ui.Output(c.Colorize().Color(fmt.Sprintf(
+		"[reset][bold][green]Remote state configured and pulled.")))
+	return 0
 }
 
 // disableRemoteState is used to disable remote state management,
@@ -326,9 +360,10 @@ Options:
   -disable               Disables remote state management and migrates the state
                          to the -state path.
 
-  -pull=true             Controls if the remote state is pulled before disabling.
-                         This defaults to true to ensure the latest state is cached
-                         before disabling.
+  -pull=true             If disabling, this controls if the remote state is
+                         pulled before disabling. If enabling, this controls
+                         if the remote state is pulled after enabling. This
+                         defaults to true.
 
   -state=path            Path to read state. Defaults to "terraform.tfstate"
                          unless remote state is enabled.

website/source/docs/commands/remote-config.html.markdown

@@ -73,8 +73,9 @@ The command-line flags are all optional. The list of available flags are:
 * `-path=path` - Path of the remote state in Consul. Required for the
   Consul backend.
 
-* `-pull=true` - Controls if the remote state is pulled before disabling.
-  This defaults to true to ensure the latest state is cached before disabling.
+* `-pull=true` - Controls if the remote state is pulled before disabling
+  or after enabling. This defaults to true to ensure the latest state
+  is available under both conditions.
 
 * `-state=path` - Path to read state. Defaults to "terraform.tfstate"
   unless remote state is enabled.